Upper and lower deviations of hole C11 for nominal sizes 0–500 mm, per ISO 286-1. Values in mm; "+" means larger than nominal, "-" smaller. Calculate other sizes →
| Nominal size (mm) | Upper deviation | Lower deviation | Tolerance (IT) |
|---|---|---|---|
| 0 ~ 3 | +0.120 | +0.060 | 0.060 |
| >3 ~ 6 | +0.145 | +0.070 | 0.075 |
| >6 ~ 10 | +0.170 | +0.080 | 0.090 |
| >10 ~ 18 | +0.205 | +0.095 | 0.110 |
| >18 ~ 30 | +0.240 | +0.110 | 0.130 |
| >30 ~ 40 | +0.280 | +0.120 | 0.160 |
| >40 ~ 50 | +0.290 | +0.130 | 0.160 |
| >50 ~ 65 | +0.330 | +0.140 | 0.190 |
| >65 ~ 80 | +0.340 | +0.150 | 0.190 |
| >80 ~ 100 | +0.390 | +0.170 | 0.220 |
| >100 ~ 120 | +0.400 | +0.180 | 0.220 |
| >120 ~ 140 | +0.450 | +0.200 | 0.250 |
| >140 ~ 160 | +0.460 | +0.210 | 0.250 |
| >160 ~ 180 | +0.480 | +0.230 | 0.250 |
| >180 ~ 200 | +0.530 | +0.240 | 0.290 |
| >200 ~ 225 | +0.550 | +0.260 | 0.290 |
| >225 ~ 250 | +0.570 | +0.280 | 0.290 |
| >250 ~ 280 | +0.620 | +0.300 | 0.320 |
| >280 ~ 315 | +0.650 | +0.330 | 0.320 |
| >315 ~ 355 | +0.720 | +0.360 | 0.360 |
| >355 ~ 400 | +0.760 | +0.400 | 0.360 |
| >400 ~ 450 | +0.840 | +0.440 | 0.400 |
| >450 ~ 500 | +0.880 | +0.480 | 0.400 |
Each row applies to the whole size range shown. Ranges are "over the first value, up to and including the second".
C11 is an ISO 286 tolerance class. The uppercase letter C is the fundamental deviation (which side of the nominal size the tolerance zone lies on), and the number 11 is the tolerance grade IT11 (how wide the zone is). Large clearance: C11/h11 is the shaft-basis loose running fit, used like H11/c11: farm machinery, hinges, joints exposed to dirt or heat. Typical processes for IT11: rough turning, stamping, drilling: loose fits (H11/c11), stamped parts.
On a drawing or in a specification, Ø6 C11 and 6(+0.145/+0.070) mean the same thing — the second form writes the deviations out, so nobody has to look them up. SFP product specifications always use the second form.
Click "Calc" in the last column to open the calculator, where the written-out form can be copied with one click.
| Size | Upper deviation | Lower deviation | Actual limits (mm) | |
|---|---|---|---|---|
| Ø1 | +0.120 | +0.060 | 1.060 ~ 1.120 | Calc |
| Ø1.5 | +0.120 | +0.060 | 1.560 ~ 1.620 | Calc |
| Ø2 | +0.120 | +0.060 | 2.060 ~ 2.120 | Calc |
| Ø2.5 | +0.120 | +0.060 | 2.560 ~ 2.620 | Calc |
| Ø3 | +0.120 | +0.060 | 3.060 ~ 3.120 | Calc |
| Ø4 | +0.145 | +0.070 | 4.070 ~ 4.145 | Calc |
| Ø5 | +0.145 | +0.070 | 5.070 ~ 5.145 | Calc |
| Ø6 | +0.145 | +0.070 | 6.070 ~ 6.145 | Calc |
| Ø8 | +0.170 | +0.080 | 8.080 ~ 8.170 | Calc |
| Ø10 | +0.170 | +0.080 | 10.080 ~ 10.170 | Calc |
| Ø12 | +0.205 | +0.095 | 12.095 ~ 12.205 | Calc |
| Ø13 | +0.205 | +0.095 | 13.095 ~ 13.205 | Calc |
| Ø16 | +0.205 | +0.095 | 16.095 ~ 16.205 | Calc |
| Ø20 | +0.240 | +0.110 | 20.110 ~ 20.240 | Calc |
| Ø25 | +0.240 | +0.110 | 25.110 ~ 25.240 | Calc |
| Ø30 | +0.240 | +0.110 | 30.110 ~ 30.240 | Calc |
| Ø35 | +0.280 | +0.120 | 35.120 ~ 35.280 | Calc |
| Ø40 | +0.280 | +0.120 | 40.120 ~ 40.280 | Calc |
| Ø50 | +0.290 | +0.130 | 50.130 ~ 50.290 | Calc |
| Ø60 | +0.330 | +0.140 | 60.140 ~ 60.330 | Calc |
| Ø80 | +0.340 | +0.150 | 80.150 ~ 80.340 | Calc |
| Ø100 | +0.390 | +0.170 | 100.170 ~ 100.390 | Calc |
The tolerance zones of the classes below lie entirely inside C11 (true for every size range from 0 to 500 mm), so they also satisfy a drawing that calls for C11. Those listed first are closest to C11; price and lead time still depend on material, size and stock.
It depends on the diameter. For Ø6, C11 means the part must measure between 6.070 and 6.145 mm, written 6(+0.145/+0.070). For other diameters see the chart above; every size range is listed.
Letters in uppercase denote a hole (inside diameter). In lowercase, c11 is a shaft tolerance, lying on the opposite side of the nominal size.
Yes. C10 is tighter than C11: at every diameter its limits fall inside the range C11 allows. The precision is simply higher than required, so the price may be a little higher.
Values follow ISO 286-1; the table was cross-checked cell by cell against three independent sources on 2026-08-26 (6,674 cells agree, 0 errors). Coverage: shafts a–z and the corresponding uppercase holes, IT1–IT13, nominal sizes 0–500 mm. cd/ef/fg/za/zb/zc, sizes above 500 mm and grades above IT13 are not included: the tool reports "not found" and never extrapolates. Data sources and verification →